Author Topic: XeLL Reloaded v0.991 released!  (Read 32107 times)

Offline tuxuser

  • Member of Free60
  • Administrator
  • User
  • *****
  • Thank You
  • -Given: 0
  • -Receive: 3
  • Posts: 296
    • http://www.libxenon.org
  • Linux Distribution: Debian Squeeze - Backports
  • XeLL Build: XeLL-Reloaded - git~HEAD
XeLL Reloaded v0.991 released!
« on: Feb 19, 2012, 22:48:36 »
A new XeLL Reloaded Release is here - v0.991

Changelog
Quote
v0.991 - 19/02/2012
! Fixing booting of Linux Kernel on Reset Glitch Hack Consoles !
Write stackdump on fail to screen
additional offsets for reloading XeLL/updating XeLL-Reloaded
integrated cOz's rawflash application (look at README)
probably fixing freezing at "Reinit PHY..."
kboot.conf parsing (shows a menu inside XeLL, loads linux and homebrew elfs - look at README)
Fixing TFTP ACK on end of file
Fixing TFTP transfer for files with only 1 DATA block
Fixing possible buffer overflow when uncompressing gzipped file
dcbst the memory-range for Devtree and Initrd

Readme
Quote
XeLL-Reloaded

A Xenon Linux loader based on Xell by tmbinc(Felix Domke)

Contributed to by:
[cOz]
Cancerous1
Ced2911
GliGli
Juvenal
Natelx
Redline99
sk1080
Tuxuser
... and you?

XeLL-Reloaded catches CPU threads, sets them up, loads an ELF file from either network (tftp), USB(fat), CDROM (ISO9660) or HDD(fat), and launches it. It's made to boot Linux, so it contains a flat device tree for Linux. However, it is able to load other ELF files as well, like applications based on LibXenon.

* Now based on LibXenon
* Supports the new Reset Glitch Hack - RGH. (xell-gggggg)
* XeLL-Reloaded is now divided in 2 stages:
   - 1st Stage initializes the Hardware, uncompresses and executes 2nd Stage
   - 2nd Stage (based on LibXenon) loads all required drivers and does the usual "XeLL tasks"
* XeLL can unzip & load gzipped files
* Support for HDMI, and properly switches NTSC/PAL on composite.
* All CPU Cores are active and ready to run at full speed.
* TinyEHCI is used, delivers full USB 2.0 speed when accessing mass storage media
* lwip network stack upgraded to v1.4 Final - It's faster and DHCP is improved.
* It can access the DVD-drive via DMA now: faster reading
* It's possible to reload into XeLL now when you are inside a LibXenon Application
* New HTTP web interface to retrieve nand dump.
* Improved hardware initialization now allows chain-loading.
* Supports upgrading with a 2-stage XeLL-Reloaded binary, named "updxell.bin"
* Infinite boot loop when looking for ELFs to execute.(no more rushing to get the live-cd in)
* Parses / decrypts keyvault
* Supports kboot.conf-type file
* Supports external initramfs
* Can pass a custom CMDLINE to linux kernel via kboot.conf
  kboot.conf/initrd support - copyright (C) 2010-2011  Hector Martin "marcan" <hector@marcansoft.com>
* Shows a user controllable menu for the parsed bootentries
  xell user prompt - by Georg Lukas "Ge0rg" <georg@op-co.de>

  HOW TO USE
==============

XeLL Reloaded checks for *.elf(homebrew/linux elf32)/kboot.conf/updxell.bin or updflash.bin in the following order:

USB (FAT):   updflash.bin
      updxell.bin
      kboot.conf
      xenon.elf
      xenon.z
      vmlinux
Network:    DHCP supplied bootserver and bootfile-name. You can supply a static tftpserver ip via kboot.conf. If no tftpserver is found, it falls back to a static ip.
      ( no updxell or updflash support via tftp)
DVD (ISO9660):   *same as USB*   
HDD (FAT):   *same as USB*


updflash.bin is a already remapped flashimage/nandimage. 16MB file for 16MB NAND and 64MB file for 64/256/512MB NAND.

updxell.bin is a renamed xell*.bin file. * Version depending on the used hack (JTAG XeLL: xell-1f, RGH XeLL: xell-gggggg)

kboot.conf (modified for XeLL) is a configfile
   General XeLL config: Set TFTP-Server, CPU-Speedup, videomode, NetConfig
   Menu: Parses bootentries, shows a user controlable menu with XboxController/UART/IR Remote
         It can parse bootarguments for linux kernels & can load initramfs/initrd

xenon.elf/xenon.z/vmlinux can be either gzipped or bare ELF32 binaries - LINUX or Homebrew

There's also a HTTP Server running while XeLL searches for executable binaries.
It can serve the CPUKey/DVDKey and the console's flashdump.


  UPDATING XELL
=================

1. Rename the appropriate XeLL-binary to "updxell.bin".
2. Copy the updxell.bin file to the root of the FAT/FAT32 USB Stick or burn a ISO9660 CD
3. Plug in the USB Stick/CD and boot up XeLL. It should find the update and flash it
4. Reboot your Xbox and enjoy the fresh XeLL build

Troubleshooting:

updxell.bin doesn't get found / updxell process doesn't start: You have to rebuild your whole hackimage with a recent XeLL. From there on you can use the inbuilt update feature
updxell function reports that no XeLL binary was found in NAND: Either your XeLL in NAND is too old or it's not a XeLL Reloaded binary - You have to rebuild your whole hackimage with a recent XeLL.


  FLASHING NAND
=================

1. Rename the new (already remapped) flashimage to "updflash.bin"
2. Copy the updflash.bin file to the root of the FAT/FAT32 USB Stick or burn a ISO9660 CD
3. Plug in the USB Stick/CD and boot up XeLL. It should find the update and flash it
4. Reboot your Xbox and enjoy the new image

Troubleshooting:

XBox does not boot properly after flashing the NAND: Either your image wasn't properly remapped or you made something wrong while building the image


  USING KBOOT.CONF
===================

1. Read and understand the kboot.conf.sample which is part of every XeLL release with kboot-support
2. Modify the file to your needs
3. Copy it, named as "kboot.conf, to a CD/FAT32 USB Stick/FAT32 HDD or supply it via TFTP
4. Boot XeLL and wait till it loads the file and shows the menu
5. Navigate to the desired bootentry. You can do this in the following ways:
   UART:   
   UP/DOWN to go up and down in the menu
   ENTER to confirm your choice
   C to cancel the menu

   X360 Controller (1st):
   DPAD-UP/DPAD-DOWN to go up and down in the menu
   A to confirm your choice
   B to cancel the menu

   X360 Media Remote:
   UP/DOWN to go up and down in the menu
   OK to confirm your choice
   Press the NUMBER of the desired bootentry to directly load it
   B to cancel the menu

6. Let the bootentry load. Enjoy :)

Troubleshooting:

kboot.conf gets found but it doesn't show bootentries or autoloads a bootentry:
Make sure timeout is set to something higher than 0
Make sure you didn't forget the "" on the bootentry: label="kernelpath params"


DOWNLOAD: Thread

I have no idea what I am doing but atleast I am trying

Offline luke69

  • User
  • *
  • Thank You
  • -Given: 0
  • -Receive: 0
  • Posts: 1
Re: XeLL Reloaded v0.991 released!
« Reply #1 on: Feb 20, 2012, 00:20:14 »
Awesome! Thanks  ;D

Offline Doerek

  • User
  • *
  • Thank You
  • -Given: 0
  • -Receive: 0
  • Posts: 50
    • Evo-X Community Magazin
  • Linux Distribution: [VMware] Ubuntu
  • XeLL Build: Xell-Reloaded (2Stages)
Re: XeLL Reloaded v0.991 released!
« Reply #2 on: Feb 20, 2012, 16:27:27 »
Now...let's do the guys from Libxenon.org a favor:
~> Spread this news to every JTAG/RGH User/Community.

Offline john.wayne

  • User
  • *
  • Thank You
  • -Given: 0
  • -Receive: 0
  • Posts: 5
Re: XeLL Reloaded v0.991 released!
« Reply #3 on: Feb 20, 2012, 17:57:49 »
will it fix overscan problem?

Offline JPizzle

  • User
  • *
  • Thank You
  • -Given: 0
  • -Receive: 0
  • Posts: 4
Re: XeLL Reloaded v0.991 released!
« Reply #4 on: Feb 20, 2012, 21:29:31 »
thanks for the update guys, appreciate all your hard work.  ;)

Offline greator

  • User
  • *
  • Thank You
  • -Given: 0
  • -Receive: 0
  • Posts: 12
  • XeLL Build: Xell Reloaded
Re: XeLL Reloaded v0.991 released!
« Reply #5 on: Mar 01, 2012, 18:32:43 »
  FLASHING NAND
=================

1. Rename the new (already remapped) flashimage to "updflash.bin"
2. Copy the updflash.bin file to the root of the FAT/FAT32 USB Stick or burn a ISO9660 CD
3. Plug in the USB Stick/CD and boot up XeLL. It should find the update and flash it
4. Reboot your Xbox and enjoy the new image

Troubleshooting:

XBox does not boot properly after flashing the NAND: Either your image wasn't properly remapped or you made something wrong while building the image

So does this mean that, Rawflash is not needed anymore?
I can flash image without opening rawflash xenon.elf?

Offline tuxuser

  • Member of Free60
  • Administrator
  • User
  • *****
  • Thank You
  • -Given: 0
  • -Receive: 3
  • Posts: 296
    • http://www.libxenon.org
  • Linux Distribution: Debian Squeeze - Backports
  • XeLL Build: XeLL-Reloaded - git~HEAD
Re: XeLL Reloaded v0.991 released!
« Reply #6 on: Mar 02, 2012, 01:33:56 »
So does this mean that, Rawflash is not needed anymore?
I can flash image without opening rawflash xenon.elf?

Correct!
I have no idea what I am doing but atleast I am trying

Offline greator

  • User
  • *
  • Thank You
  • -Given: 0
  • -Receive: 0
  • Posts: 12
  • XeLL Build: Xell Reloaded
Re: XeLL Reloaded v0.991 released!
« Reply #7 on: Mar 16, 2012, 20:22:19 »
Unfortunately, this doesn't work for me. It just cant glitch.
First I thought it must be my wiring. But when I flash the old [xell-reloaded-2stage-2011-09-23], it works.
So its not my wiring, its just that new ecc file doesn't work on me. :(